IR Remote control shortcuts
August 10, 2023
Here are all the current PTZOptics Ir commands that can be done from the supplied IR remote control. These commands are done in succession, not all at once. The OSD will be shown over top of any live image from the camera. If you don't see all these commands working on your camera make sure your unit is fully firmware updated. https://ptzoptics.com/firmware-finder/
These are the shortcuts for the G2 line of cameras.
[*] + [#] + [F1]: IR Address 1
[*] + [#] + [F2]: IR Address 2
[*] + [#] + [F3]: IR Address 3
[*] + [#] + [F4]: IR Address 4
[*] + [#] + [1]: Displays OSD menu in English
[*] + [#] + [3]: Displays OSD menu in Chinese
[*] + [#] + [4]: Displays IP address
[*] + [#] + [6]: Quickly restore default settings
[*] + [#] + [8]: Show the camera firmware version
[*] + [#] + [9]: Quickly set mounting mode (vertical flip / normal)
[*] + [#] + [MANUAL]: Resets IP information
[#] + [*] + [4]: Toggles DHCP or Static IP configuration
[#] + [*] + [#] + [1]: Set IP address to: 192.168.100.81
[#] + [*] + [#] + [2]: Set IP address to: 192.168.100.82
[#] + [*] + [#] + [3]: Set IP address to: 192.168.100.83
[#] + [*] + [#] + [4]: Set IP address to: 192.168.100.84
[#] + [*] + [#] + [5]: Set IP address to: 192.168.100.85
[#] + [*] + [#] + [6]: Set IP address to: 192.168.100.86
[#] + [*] + [#] + [7]: Set IP address to: 192.168.100.87
[#] + [*] + [#] + [8]: Set IP address to: 192.168.100.88
[#] + [*] + [#] + [9]: Set IP address to: 192.168.100.89
[#] + [*] + [#] + [0]: Set IP address to: 192.168.100.80
These are the shortcuts for the MOVE line of cameras (4K, SE, and Link)
[F1]: Enable video-based auto framing (nonfunctional)
[F2]: Enable audio-based auto-tracking (nonfunctional)
[F3]: Enable video-based auto tracking
[F4]: Disable auto tracking
[*] + [#] + [1]: Sets OSD Menu to English
[*] + [#] + [3]: Sets OSD Menu to Chinese
[*] + [#] + [6]: Quickly restore default settings
[*] + [#] + [8]: Show the camera firmware version
[*] + [#] + [4]: Show camera’s IP address
[#] + [*] + [F1]: Increase the IR Remote’s control speed by 0%
[#] + [*] + [F2]: Increase the IR Remote’s control speed by 10%
[#] + [*] + [F3]: Increase the IR Remote’s control speed by 20%
[*] + [#] + [MANUAL]: Resets camera IP information
[#] + [*] + [4]: Enables DHCP
[#] + [*] + [#] + [1]: Set IP address to: 192.168.100.81
[#] + [*] + [#] + [2]: Set IP address to: 192.168.100.82
[#] + [*] + [#] + [3]: Set IP address to: 192.168.100.83
[#] + [*] + [#] + [4]: Set IP address to: 192.168.100.84
[#] + [*] + [#] + [5]: Set IP address to: 192.168.100.85
[#] + [*] + [#] + [6]: Set IP address to: 192.168.100.86
[#] + [*] + [#] + [7]: Set IP address to: 192.168.100.87
[#] + [*] + [#] + [8]: Set IP address to: 192.168.100.88
[#] + [*] + [#] + [9]: Set IP address to: 192.168.100.89
[#] + [*] + [#] + [0]: Set IP address to: 192.168.100.80
[*] + [#] + [F1]: Sets camera IR to address 1
[*] + [#] + [F2]: Sets camera IR to address 2
[*] + [#] + [F3]: Sets camera IR to address 3
[*] + [#] + [F4]: Sets camera IR to address 4
[L/R SET] + [1] (STD): Normal Pan controls
[L/R SET] + [2] (REV): Reversed Pan controls
[*] + [#] + [9]: Quickly set mount mode (flip / normal)
[#] + [*] + [7]: OnePush White Balance Trigger
[*] + [*] + [F3]: Toggle the HDMI / SDI output
[#] + [*] + [F4]: Freezes the video feed. Repeat to unfreeze.
[PRESET] + [0-9]: Sets camera preset
[RESET] + [0-9]: Erase camera preset
[*] + [#] + [RESET]: Quickly erase all PTZ presets
[*] + [#] + [AUTO]: Perform startup dance on repeat